Okin Betadrive 1.25.000.158.30
Electric Recliner Motor ReplacementÂ
CouchGuard® for electric recliner parts including the electric recliner motor. The actuator as it is known, comes in the standard industry length 535mm and is also available as a kit which contains the actuator  power supply, extension cable and the figure 8 power cable. We also provide a 1 year warranty on ALL our electric recliner parts. Data Spec Sheet below. Scroll down or swipe up to discover more  Â
We also provide a 1 year warranty on ALL our electric recliner parts. Australian Owned Company.Â
Please also note this is not a lift chair actuator.
Electric recliner motor suites a standard electric recliner chair. Genuine Okin Betadrive 1.25.000.210.30, 1.25.000.211.30, 1.25.000.214.30, 1.25.000.215.30, 1.25.000.139.30 use the 1.25.000.158.30
-
Liz KennettJul 27, 2020, 09:03 AMI received my order in good time and has been fitted to the recliner and working perfectly.
-
Charles Vella VellaJul 10, 2020, 07:28 AMThank you for the actuators and the prompt delivery. Wasn’t expecting them until next week.
Received and installed and all is like new. -
Stewart BrettJun 2, 2020, 05:41 AMBrilliant service
-
William GirlingJun 3, 2019, 05:21 PMJust a note to say thank you.
-Ordered by me 30 May
-despatched by you 31 May
-received by me 3 June
-successfully installed by me 3 June.
Thanks, I can again put my feet up.
William
Removing & Fitting A Actuator
1 Place a drop sheet or old towels around the recliner.
2 Turn off and remove the power supply plug from the mains.
3 Gently turn the recliner over onto its side or on its back. Remember correct lifting methods.
4 Locate the component and its lead. Follow the lead along to the plug ends remembering where it runs.
5 Using a pair of side cutters, snip the cable ties that are retaining the lead to the frame.
6 Loctate the two mounting pins and clips that hold the motor to the frame. Remove the wire retaining clips from the pins using a pair of pointy noise pliars. Hold the motor and remove the pins.
7 Place the new motor assmebly into position. Replace the pins through the mounting holes and attach the wire clips.
8 Plug in all leads and run them along the frame. Check that all leads are out of the way of moving parts. Cable tie the leads back to the frame.
9 Turn the recliner back over to normal seating position
10 Plug the main power supply back into the wall.
11 Test the new component. Operate the lift chair recliner to its fullest position and check that all the leads are clear and not stretched.
12 Return the lift chair to its normal seating position.
DO NOT exceed more then 2 mins operating time at anyone time.
If you do exceed this time, wait 20 mins before using again.
Universal Actuator Measurements
The universal actuators have an overall length of 535mm and a stroke of 340mm. This is industry standard and also has then "0I" power lead plus contains the female 5 pin plug mounted in the body of the motor. This overall measurement is from the center of the clevis pin mounting hole to the center of the mounting nut on the opposite end. Please refer to our Data Spec Sheet. The stroke is the distance the white plastic guide travels .Â
This kit also comes with a 1 year warranty.
535mm Universal Actuator Specifications
- Input Voltage:
- 24V DC
- Max Load Capacity:
- 750N (100kgs)
- Max Speed:
- 30mm/s
- Std Stroke:
- 340mm
- Overal Length:
- 535mm
- Limit Switch:
- Inner
- Type Of Duty:
- S2 - 10mins
- Protection Class:
- IP43
- Controller Plug:
- Built in 5pin Female
- Power Wire Plug:
- Standard 0I Plug
- Cercification:
- CE / EMC+LVD
All recliner parts are universal. Makes of recliners, brand names or manufactures part numbers don't mean much to us.
Universal Actuator Measurments
The universal actuators have an overall length maximum length of 685mm with a minimum install length of 445mm and a stroke of 240mm. This is industry standard and also has then "0I" power lead plus the 5 pin plug control plug. This overall measurement is from the center of the clevis pin mounting holes.Â
Please refer to our Data Spec Sheet for more info on measurements.Â
This kit also comes with a 1 year warranty.
240mm Actuator Specifications
- Input Voltage:
- 24V DC
- Max Load Capacity:
- 2000N (200kgs)
- Max Speed:
- 20mm/s
- Std Stroke:
- 240mm
- MIN Install:
- 445mm
- Limit Switch:
- Inner
- Type Of Duty:
- S2 - 10mins
- Protection Class:
- IP43
- Cercification:
- CE / EMC+LVD
- Power Wire Plug:
- Standard 0I Plug
- Hand Control Plug:
- Female 5 Pin Plug
A Universal Actuator Kit Contains
- Actuator:
- x 1
- 0I Extension Cable:
- x 1
- Power Supply:
- x 1
- Power Cable:
- x 1